Showing 289–304 of 368 results
-
SPEED CONTROL OF INDUCTION MOTOR USING ACPWM
₹8,400.00₹7,400.00This project attempts a new speed control technique for the single-phase a.c. induction motor. It presents a design of a low-cost; high-efficiency drive capable of supplying a single-phase a.c. induction motor with a PWM modulated sinusoidal voltage. The circuit operation is controlled by an 8051 family microcontroller.
-
Speed Control Of Induction Motor Using Firing Angle Control
₹7,500.00₹5,900.00The main object of this project is to develop speed control of two induction motor using firing angle control system which is helpful to control the speed of an induction motor using microcontroller
In this project, the zero-crossing point of the voltage waveform is detected by a comparator whose output is then fed to the microcontroller. Then, it provides the required delayed triggering pulses to a pair of TRIAC through an opto-isolator connected to this circuit. Finally, power is applied to the load through the TRIAC. Four push-button switches are interfaced to the controller for increasing and decreasing the AC power to the load. In this project, a lamp is used in the place of induction motor demonstration purposes. The motor speed variation depends on the power reduction.
-
SPEED CONTROL OF TWO INDUCTION MOTOR USING ACPWM
₹10,500.00₹8,600.00This project attempts a new speed control technique for the single-phase a.c. induction motor. It presents a design of a low-cost; high-efficiency drive capable of supplying a single-phase a.c. induction motor with a PWM modulated sinusoidal voltage. The circuit operation is controlled by an 8051 family microcontroller. The device is aimed at substituting the commonly used triac phase angle control drives. The circuit is capable of supplying a single-phase a.c. induction motor (or general a.c. inductive/resistive load) with varying a.c. voltage. The same as in triac control, the voltage applied to the load can be varied from zero to maximum value. On the other hand, it uses a pulse width modulation technique (PWM), and when compared with the phase angle control used for triacs, produces much lower high order harmonics.
-
STREET LIGHT THAT GLOWS ON DETECTING VEHICLE MOVEMENT
₹7,500.00₹5,000.00This project is designed to detect a vehicle movement on road to switch on only a block of street lights that are ahead of the vehicle, and to switch off the glowing lights when the vehicle passes away from the lights. This will help to save electrical energy.
-
SUBSTATION MONITORING OVER IOT
₹10,500.00₹8,800.00The purpose of this project is to acquire the remote electrical parameters like voltage, current and frequency and send these real time values over network along with temperature at power station. This project is also designed to protect the electrical circuitry by operating a relay.
-
SUN TRACING SOLAR PANEL IN TWO AXIS USING ARDUINO AND SERVO MOTORS
₹9,400.00₹8,400.00The variation in the solar energy occur daily due to variation in day night cycle and also because of seasonal variations through out the year. Population of the world is increasing very rapidly. From past decade of years the non renewable energy sources like coal and oil are extinguishing and so it become serious problem for providing he reliable energy to the world. But solar energy plays important source of primary energy. In this project we propose dual axis solar tracking system by which it is possible to catch maximum amount of solar energy by using Arduino as main processing unit.
-
SUN TRACKING SOLAR PANEL
₹7,500.00₹5,000.00This project employs a solar panel mounted to a time-programmed stepper motor to track the sun so that maximum sun light is made incident upon the panel at any given time of the day. This is better compared to the light-sensing method that may not be accurate always – for example, during cloudy days.
-
-12%Sun tracking solar panel
₹16,500.00₹14,500.00Now a days as a source of renewable energy solar energy is becoming very popular. When sun rays fall on Photovoltaic panel, Panel converts it in to electrical energy. As per basic principles of solar photovoltaic cells maximum electrical energy is generated when rays collide panel in perpendicular direction.
If we mount solar panel at single angle & position we will be unable to utilize 100% solar energy. To achieve the above target we need to rotate solar panel as sun moves from east to west.
