11 Level Multilevel Inverter

All Projects

Showing 1–16 of 363 results

  • 4.80 out of 5

    11 Level Multilevel Inverter

    15,000.00 14,000.00

    This project presents the hardware implementation of the single phase  in eleven  level multilevel inverter using the Cascaded HBridge using Separated DC sources. The main objective of is to increases the number of levels with a lower number of switches at the output without adding any complexity to the power circuit

    Select options
  • 4.75 out of 5
    -15%

    360 Degree Steering Mechanism

    20,000.00 17,000.00

    Main objective of this project is to develop a steering mechanism that vehicle will be steered at single position.

    Add to cart
  • 4.71 out of 5

    7 Level Multilevel Inverter

    12,000.00 11,000.00

    This project presents the hardware implementation of the single phase  in seven level multilevel inverter using the Cascaded HBridge using Separated DC sources. The main objective of is to increases the number of levels with a lower number of switches at the output without adding any complexity to the power circuit.

    Select options
  • 4.67 out of 5

    AC DIMMER OF TWO LOADS USING SINGLE CONTROLLER

    8,500.00 6,000.00

    This project is intended to attain AC dimmer of two loads using single controller. It is a renowned and aged technique of managing AC power, principally across linear loads for instance heaters brought into play in electric oven.
    In this project, we are using a comparator for zero crossing detection which is fed as an interrupt to the arduino UNO3. Here, the arduino delivers the output based on the interrupt received as the reference for generating triggering pulses. Using these pulses, we drive the Opto-isolators for triggering the TRIAC to achieve integral cycle control as per the input switches interfaced to the arduino. In place of a linear load to be used in the output, a series motor or lamp can be used to verify the output. A lamp is provided in this project in place of a motor for demonstration purpose. The project output with a lamp appears to be a simple project of lamp flickering but the real objective is to verify in a CRO/DSO ,whether at the random switching also the load switches on at zero cross of the waveform or not.

    Select options
  • 4.50 out of 5

    AC DIMMER TO CONTROL AC VOLTAGE, SPEED OF INDUCTION MOTOR OR HEATER COIL

    4,400.00 3,400.00

    A voltage controller, also called an AC voltage controller or AC regulator is an electronic module based on either thyristors, TRIACs, SCRs or IGBTs, which converts a fixed voltage, fixed frequency alternating current (AC) electrical input supply to obtain variable voltage in output delivered to a resistive load.

    Induction motor speed control is done by varying the frequency of the applied voltage. Raising or lowering the voltage can have some speed control effects but these will be small, difficult to control, load-dependent, possibly cause the motor to overheat and, are not generally recommended.

    Select options
  • 4.67 out of 5

    ACCIDENT DETECTION BY USING ACCELEROMETER ALCOHOL SENSOR GSM

    9,800.00 8,600.00
    Select options
  • 4.50 out of 5
    -10%

    ACKERMAN STEERING MECHANISM

    10,500.00 9,500.00

    There are many types o steering mechanisms used in automotive vehicles. In this project we have made prototype of Ackerman steering mechanism.

    Add to cart
  • 4.25 out of 5

    ACPWM power control using 555IC and IGBT

    5,200.00 4,200.00

    This project attempts a new speed control technique for the single-phase a.c. induction motor. It presents a design of a low-cost; high-efficiency drive capable of supplying a single-phase a.c. induction motor with a PWM modulated sinusoidal voltage. The circuit operation is controlled by 555 astable multivibrator. The device is aimed at substituting the commonly used triac phase angle control drives. The circuit is capable of supplying a single-phase a.c. induction motor (or general a.c. inductive/resistive load) with varying a.c. voltage.

    Select options
  • 4.67 out of 5

    ADVANCE ATM SECURITY SYSTEM

    11,000.00 9,500.00

    The Idea of Designing and Implementation of Security Based ATM theft project is born with the observation in our real life incidents happening around us. This project deals with prevention of ATM theft from robbery. So overcome the drawback found in existing technology in our society. Vibration sensor is used here which senses vibration produced when ATM machine is hammered. This system uses Arduino based system to process real time data collected using the vibration sensor. Once the vibration is sensed the beep sound will occur from the buzzer. DC Motor is used for closing the door of ATM and send with the message to the nearby police station and corresponding authorized person through the GSM.

    Select options
  • 4.50 out of 5

    ADVANCE CAR JACK CONTROLLED BY RF WIRELESS DEVICE

    14,000.00 9,200.00

    The project is designed to control the direction of car jack by using a RF technology for remote operation with a transmitter and receiver. The direction of the DC motor is depending on signal which is coming from transmitter. Hence, if the relay 1 & relay 4 gets ON then the motor rotates in forward direction. And if relay 2 & relay 3 gets ON then the motor rotates in backward direction.

    Select options
  • 4.00 out of 5

    ADVANCE GREEN HOUSE WITHOUT MICROCONTROLLER

    9,600.00 8,500.00

    This project is designed to monitor the green house using Comparator IC. Various sensors are used to monitor the system. The sensors used are Rain sensor, Soil moisture sensor, LDR, wired security sensor, water level indicator, IR sensor. When the soil of the green house becomes dry the pump will turn on through which the water is let into the soil and the soil regains its moisture. While supplying the water to the dry soil the water level in tank will be reducing simultaneously which will be indicated by the LED’s.
    So when the water level reduces below the threshold level the pump will off automatically to avoid dry run.

    Select options
  • 4.25 out of 5

    ADVANCED BLIND STICK USING ARDUINO

    6,000.00 4,000.00

    The system consists of obstacle detection sensors for receiving, processing, and sending signals to the alarm system which finally alerts the user for prompt action.

    Select options
  • 4.33 out of 5

    ADVANCED BUS WITH AUTOMATIC TICKETING, STUDENT PASS FACILITY, BALANCE CALCULATION AND SMS ALERT

    11,000.00 8,500.00

    The aim of this project is to implement advanced bus with automatic ticketing, student pass facility, balance calculation and SMS alert. This system is used for automatic ticket generation, student bus pass information as well as balance calculation for each ticket and balance, validity alert message on user’s mobile phones.
    The most of people in India uses bus travelling facility in their daily routine life. The manual use of bus reservation is presently very troubled thing and also consumes a lot of time by having to stay on a long queue. For this reason, an efficient system is to be proposed in this project to ease the issue of bus ticketing within the country.

    Select options
  • 0 out of 5

    ADVANCED EV CHARGING STATION OVER IOT

    11,500.00 10,500.00
    Select options
  • 4.25 out of 5

    ADVANCED GREEN HOUSE

    8,500.00 7,800.00

    This Advance project is designed to monitor the green house using Arduino controller. Various sensors are used to monitor the system. The sensors used are Rain sensor, Soil moisture sensor, DHT 11 sensor, fire detector and LDR. Multiple sensors are used to control various parameters. LCD is used to display the status of parameters

    Select options
  • 4.20 out of 5

    ADVANCED GREEN HOUSE OVER GSM

    10,000.00 9,000.00

    This Advance project is designed to monitor the green house using Arduino controller. Various sensors are used to monitor the system. The sensors used are Rain sensor, Soil moisture sensor, DHT 11 sensor, fire detector and LDR. GSM is used to send parameters status to the respective person on cellular phone. Respective person will take action on parameters status through cellular phone.

    Select options

Select your currency
×