SPEED CONTROL OF INDUCTION MOTOR USING ACPWM

Electrical Projects

Showing 161–176 of 214 results

  • 4.50 out of 5

    SPEED CONTROL OF INDUCTION MOTOR USING ACPWM

    8,400.00 7,400.00

    This project attempts a new speed control technique for the single-phase a.c. induction motor. It presents a design of a low-cost; high-efficiency drive capable of supplying a single-phase a.c. induction motor with a PWM modulated sinusoidal voltage. The circuit operation is controlled by an 8051 family microcontroller.

    Select options
  • 4.45 out of 5

    SPEED CONTROL OF INDUCTION MOTOR USING ANDROID

    7,400.00 6,400.00

    The main intention of this project is to develop an induction motor speed control system which is helpful to control the speed of an induction motor using TRIAC.

    Select options
  • 4.33 out of 5

    Speed Control Of Induction Motor Using Firing Angle Control

    7,500.00 5,900.00

    The main object of this project is to develop speed control of two induction motor using firing angle control system which is helpful to control the speed of an induction motor using microcontroller

    In this project, the zero-crossing point of the voltage waveform is detected by a comparator whose output is then fed to the microcontroller. Then, it provides the required delayed triggering pulses to a pair of TRIAC through an opto-isolator connected to this circuit. Finally, power is applied to the load through the TRIAC. Four push-button switches are interfaced to the controller for increasing and decreasing the AC power to the load. In this project, a lamp is used in the place of induction motor demonstration purposes. The motor speed variation depends on the power reduction.

    Select options
  • 4.60 out of 5

    Speed control of stepper motor using 8051 microcontroller

    6,400.00 5,400.00
    Select options
  • 4.67 out of 5

    SPEED CONTROL OF TWO INDUCTION MOTOR USING ACPWM

    10,500.00 8,600.00

    This project attempts a new speed control technique for the single-phase a.c.   induction motor. It presents a design of a low-cost; high-efficiency drive capable of supplying a single-phase a.c.   induction motor with a PWM modulated sinusoidal voltage. The circuit operation is controlled by an 8051 family microcontroller. The device is aimed at substituting the commonly used triac phase angle control drives. The circuit is capable of supplying a single-phase a.c. induction motor (or general a.c. inductive/resistive load) with varying a.c. voltage. The same as in triac control, the voltage applied to the load can be varied from zero to maximum value. On the other hand, it uses a pulse width modulation technique (PWM), and when compared with the phase angle control used for triacs, produces much lower high order harmonics.

    Select options
  • 4.12 out of 5

    STREET LIGHT THAT GLOWS ON DETECTING VEHICLE MOVEMENT

    7,500.00 5,000.00

    This project is designed to detect a vehicle movement on road to switch on only a block of street lights that are ahead of the vehicle, and to switch off the glowing lights when the vehicle passes away from the lights. This will help to save electrical energy.

    Select options
  • 4.40 out of 5

    SUBSTATION MONITORING OVER GSM WITH FLOOD AND EARTH QUICK DETECTION

    10,000.00 9,000.00
    Select options
  • 4.57 out of 5

    SUBSTATION MONITORING OVER IOT

    10,500.00 8,800.00

    The purpose of this project is to acquire the remote electrical parameters like voltage, current and frequency and send these real time values over network along with temperature at power station. This project is also designed to protect the electrical circuitry by operating a relay.

    Select options
  • 4.57 out of 5

    SUBSTATION MONITORING USING ARDUINO OVER GSM

    9,400.00 8,400.00
    Select options
  • 4.50 out of 5

    SUN TRACKING SOLAR PANEL

    7,500.00 5,000.00

    This project employs a solar panel mounted to a time-programmed stepper motor to track the sun so that maximum sun light is made incident upon the panel at any given time of the day. This is better compared to the light-sensing method that may not be accurate always – for example, during cloudy days.

    Select options
  • 4.20 out of 5

    Sun Tracking Solar Panel

    13,000.00 12,000.00

    In this project, LDR’s are working as light detectors. Before we go into detail, we will have to understand how the LDR’s work. LDR (Light Dependent Resistor) also known as photo resistor is the light sensitive device. Its resistance decrease when the light falls on it and that’s why it is frequently used in Dark or Light Detector Circuit. Check the various circuits based on LDR here.

    Select options
  • 5.00 out of 5

    SUN TRACKING SOLAR PANEL TO TRACK THE MAXIMUM RAYS BY USING SERVO MOTOR

    9,500.00 7,400.00

    This project employs sun tracking solar panel to track the maximum rays by using servo motor. This is better compared to the light-sensing method that may not be accurate always – for example, during cloudy days. With the impending scarcity of non-renewable resources, people are considering to use alternate sources of energy. Barring all the other available resources, the solar energy is the most abundant and it is comparatively easy to convert into electrical energy. The usage of solar panel to convert Sun energy into electrical energy is very popular, but due to the transition of sun from east to west, the fixed solar panel may not be able to generate optimum energy. The proposed system solves this problem by an arrangement for the solar panel to track the maximum Sun rays.

    Select options
  • 4.00 out of 5

    SUN TRACKING SOLAR PANEL TO TRACK THE MAXIMUM RAYS USING LDR’S

    7,600.00 5,800.00

    This project employs sun tracking solar panel to track the maximum rays using ldr’s. This is better compared to the light-sensing method that may not be accurate always – for example, during cloudy days. With the impending scarcity of non-renewable resources, people are considering to use alternate sources of energy. Barring all the other available resources, the solar energy is the most abundant and it is comparatively easy to convert into electrical energy. The usage of solar panel to convert Sun energy into electrical energy is very popular, but due to the transition of sun from east to west, the fixed solar panel may not be able to generate optimum energy. The proposed system solves this problem by an arrangement for the solar panel to track the maximum Sun rays.

    Select options
  • 4.00 out of 5

    SUN TRACKING SOLAR PANEL WITH STREET LIGHT CONTROL

    5,900.00 5,500.00

    This project employs a solar panel mounted to a time-programmed stepper motor to track the sun so that maximum sun light is made incident upon the panel at any given time of the day. This is better compared to the light-sensing method that may not be accurate always – for example, during cloudy days.
    With the impending scarcity of non-renewable resources, people are considering to use alternate sources of energy. Barring all the other available resources, the solar energy is the most abundant and it is comparatively easy to convert into electrical energy. The usage of solar panel to convert Sun energy into electrical energy is very popular, but due to the transition of sun from east to west, the fixed solar panel may not be able to generate optimum energy. The proposed system solves this problem by an arrangement for the solar panel to track the Sun.

    Select options
  • 4.50 out of 5

    SUPER FAST ELECTRONIC CIRCUIT BREAKER

    7,500.00 5,000.00

    The project is designed to shut down a power supply when it is overloaded by using a super-fast electronic circuit breaker. The concept of electronic circuit breaker came into focus realizing that the conventional circuit breakers such as MCBs take longer time to trip. Therefore, for sensitive loads, it is very important to activate a tripping mechanism at the shortest possible time, preferably instantaneously.

    Select options
  • 4.50 out of 5

    SUPER / ULTRA FAST ELECTRIC CIRCUIT BREAKER

    6,300.00 3,600.00

    The project is designed to shut down a power supply when it is overloaded by using a super-fast electronic circuit breaker. The concept of electronic circuit breaker came into focus realizing that the conventional circuit breakers such as MCBs take longer time to trip. Therefore, for sensitive loads, it is very important to activate a tripping mechanism at the shortest possible time, preferably instantaneously.

    Select options

Select your currency
×